s2 11.0 sailboat for sale

JavaScript seem to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website.

Edwards Yacht Sales

• 866.365.0706

1981 S2 11.0A

• Delray Beach, FL, US

Yacht price

• Email Broker
• Call Broker

Performance Cruiser - Quality Build - Turn Key

S2 Yachts were built in Holland, Michigan from 1974 thru 1989. Known for good build quality and sailing characteristics. ALOHA has been loved and updated by the seller since 2006. Set-up for short handed sailing and equipped for comfortable cruising - ALOHA will not disappoint.

Check this out:

• Less than 1000 hours on the 2009 rebuilt Volvo diesel
• Super Sailmakers 135 Head Sail, (2016)
• North Sails Main Sail, (2016)
• Mast, Pulled, Inspected & Painted (2010)
• Sta-Lok Standing Rigging by Andrew Wall
• LED Lighting - Interior, Steaming and Deck
• AIR Breeze Wind Generator
• Solar Panel, Siemens 75 Watt
• Toilet, Raritan LECTRA/SAN MC
• New Bottom Paint Oct 2015

Don't hesitate - make an appointment to see ALOHA today!

Specifications

Descriptions, basic information, dimensions & weight.

• View Option

Measurements

• L.O.A.: 36' 00" / 10.97m
• D.W.L.: 28' 3" / 8.62m
• Beam: 11' 11" / 3.38m
• Draft: 5' 5" / 1.68m
• Bridge Clearance: 49' 00" / 14.94m
• Displacement: 15000 lbs./ 6804 kgs.
• Ballast: 6000 lbs. / 2722 kgs. (Lead)
• Keel: Fin w/Skeg Rudder
• Interior Headroom: 6' 3" / 1.8m
• Fuel: 50 gals. / 189 ltrs. Aluminum
• Fresh Water: 80 gals. / 303 ltrs. Aluminum
• Holding - (Was removed, but can be reinstalled) NO NEED On-Board Waste Treatment Raritan LECTRA/SAN MC Exceeds USCG Type I requirements and was granted Type I label certification

Accommodations

Upon entering ALOHA via the companionway the S2 timeless quality combined with pride of ownership is immediately evident. To port is the fully appointed, U-shaped galley with gimballed 2 burner range/oven, spacious top loading refrigeration and double stainless sink. Across to Starboard is the aft quarter berth which can easily sleep two. Includes teak shelf outboard, storage under and port light. The fold-down navigation table is forward of the aft quarter berth. Forward of the Nav Station and galley is built-in seating which can be used as a single berth. Along the stbd side are teak cabinets, bookshelves and storage under the settee. Across to the port side is a U-shaped settee with table. The salon table folds down to become a double berth. Forward on the stbd side is the head with vanity, shower and  Raritan LECTRA/SAN MC toilet - no need for a holding tank . The forward cabin has a V-berth, storage drawers under and hanging locker. The classic teak and holly cabin sole and teak joinery  makes the interior feel warm and inviting.

Interior Details

• R everse Cycle A/C, Marine Air - 16,000 BTU
• Interior Upholstery Replaced in 2007
• LED Lighting
• Teak and Holly Sole - Good Condition
• U-shaped design w/Formica surfaces, teak sea rails on all edges.
• Adler Barbour Refrigeration, Top Load, 12 Volt
• Gimballed two burner Alcohol Origo Stove & Oven
• Double s/s sink w/hot and cold pressure water tap, manual pump
• Upper & Lower Storage Cabinets

The head compartment includes a shower fully enclosed by a wrap-around curtain on an overhead track.  Raritan LECTRA/SAN MC toilet eliminates hose and tank oder, plus no more pump-out! Mirror, overhead hatch, opening port contoured teak vanity and convenient storage areas.

Electronics & Navigation

• Raymarine Autohelm ST6000 Wheel Autopilot 
• Datamarine Wind Instruments
• Datamarine Depth
• Datamarine Speed
• Richie Magnetic Compass at Helm & Nav Station
• VHF, ICOM, Model IC-M422
• Stereo, Jensen
• Marine Interior & Exterior Speakers
• Diesel, 35 H.P., Volvo MD17C, Less than 1000 hours on rebuild .
• 3 blade fixed propeller
• Racor Fuel/Water Separator
• Sound insulated engine compartment w/access from front and sides.
• Spares include, belts, hoses, heat exchanger, alternator

Electric & Plumbing

• Four (4) 6 Volt Golf Cart Batteries for Start & House (2017)
• Battery Charger, ProMariner ProSport12
• Air Breeze Marine Wind Generator
• Solar Panel, 75 Watt
• A/C, D/C Electrical Panel
• 30 Amp Shore Power Cord
• 12V LED Lighting Fixtures
• Water Heater, (Runs off the diesel or 110v)
• Pressure water system with hot and cold water tap in galley and head.
• Manual water pump in galley
• Electric bilge pump w/auto switch (2015)
• Manual bilge pump (2016)

Sails, Rigging & Hardware

• Aluminum Mast, Pulled, Inspected & Painted (2010)
• Super Sails 135% Roller Furling Head Sail (2016)
• North Sails Main, (2016)
• Furler, Harken (2010)
• Standing Rigging - Replaced by Andrew Wall (2007)
• Running Rigging (2006) Good Condition
• Winches, Lewmar 44 ST (2), Barient 8P (1), Lewmar 16 (1), Lewmar 30 ST (1)
• Whisker pole
• Mainsail cover
• Winch handles
• Dodger & Bimini
• Wheel Steering
• Double lifelines w/quick release hooks
• Welded s/s double bow rail & stem rail, stanchions.
• Swim ladder
• Dinghy Davits
• RIB Dinghy w/Suzuki 6 hp (2012)

Anchoring & Safety

• Windlass - Manual
• Fortress 45 lb Anchor w/Chain & Nylon Rode
• Misc. PFD's

Personal items

Brokers Comments

ALOHA is in good condition and ready for a new owner to leave the dock bound for adventure. Spacious and an excellent choice for a coastal cruiser. ALOHA is a great choice for a budget/quality minded buyer.

• Less than 1000 hours on the rebuilt Volvo diesel

The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.

Presented by

Kirk muter 2 listing(s).

• 954.649.4679 727.449.8222
• View Profile

Manufacturer

Length Range Length Range

Year Range Year Range

Price Range Price Range

QUICK SEARCH BY:

Buyer services, featured yacht.

2002 Linssen 470 Grand Sturdy

1981 Hatteras 48 Motor Yacht

2002 American Tug Pilothouse

1997 Voyage Yachts Norseman 430 Owners Version

1996 Tiara Yachts 3500 Express

1985 Ocean Yachts 55 Super Sport

2000 Manta Mark II

2005 Island Packet 485

2005 Carver 53 Voyager

1985 Morgan 31 Off Shore Fishing Cuddy

2023 Robalo R302 Center Console

2007 Meridian 391 Sedan

2008 Sea Ray 47 Sedan Bridge

2015 Lagoon 450 F

2019 Monachus Issa 45

2005 Jefferson Rivanna 50 SDMY

2007 Sea Ray Sundancer 40

• Google Plus
• Boats For Sale
• Brokerage Services
• Sold Yachts

Whether you are buying or selling your next boat or your first boat, one of Edwards Yacht Sales 45+ Professional Yacht Brokers throughout the Southeast are here to assist. Since 2003 we have acted as our clients trusted advisor throughout the entire process from shopping, to making an offer, to sea trial and survey, to closing.

Corporate Office: 510 Brookside Drive Clearwater, FL 33764

Email: [email protected]

Phone: 727.449.8222 Toll Free: 866.365.0706 Fax: 727.298.0456

Copyright © 2024 Edwards Yacht Sales Do Not Sell My Personal Information Powered by YachtCloser

We have placed cookies on your device to help make this website better.

You can use this tool to change your cookie settings. Otherwise, we’ll assume you’re OK to continue.

Some of the cookies we use are essential for the site to work.

We also use some non-essential cookies to collect information for making reports and to help us improve the site. The cookies collect information in an anonymous form.

To control third party cookies, you can also adjust your browser settings .

• New Sailboats
• Sailboats 21-30ft
• Sailboats 31-35ft
• Sailboats 36-40ft
• Sailboats Over 40ft
• Sailboats Under 21feet
• used_sailboats
• Apps and Computer Programs
• Communications
• Fishfinders
• Handheld Electronics
• Plotters MFDS Rradar
• Wind, Speed & Depth Instruments
• Anchoring Mooring
• Running Rigging
• Sails Canvas
• Standing Rigging
• Diesel Engines
• Off Grid Energy
• Cleaning Waxing
• DIY Projects
• Repair, Tools & Materials
• Spare Parts
• Tools & Gadgets
• Cabin Comfort
• Ventilation
• Footwear Apparel
• Foul Weather Gear
• Mailport & PS Advisor
• Inside Practical Sailor Blog
• Activate My Web Access
• Reset Password
• Customer Service

• Free Newsletter

Ericson 41 Used Boat Review

Mason 33 Used Boat Review

Beneteau 311, Catalina 310 and Hunter 326 Used Boat Comparison

Maine Cat 41 Used Boat Review

Tips From A First “Sail” on the ICW

Tillerpilot Tips and Safety Cautions

Best Crimpers and Strippers for Fixing Marine Electrical Connectors

Thinking Through a Solar Power Installation

Getting the Most Out of Older Sails

How (Not) to Tie Your Boat to a Dock

Stopping Mainsheet Twist

Working with High-Tech Ropes

Fuel Lift Pump: Easy DIY Diesel Fuel System Diagnostic and Repair

Ensuring Safe Shorepower

Sinking? Check Your Stuffing Box

The Rain Catcher’s Guide

Boat Repairs for the Technically Illiterate

Boat Maintenance for the Technically Illiterate: Part 1

Whats the Best Way to Restore Clear Plastic Windows?

Mastering Precision Drilling: How to Use Drill Guides

Giving Bugs the Big Goodbye

Galley Gadgets for the Cruising Sailor

Those Extras you Don’t Need But Love to Have

UV Clothing: Is It Worth the Hype?

Preparing Yourself for Solo Sailing

How to Select Crew for a Passage or Delivery

Preparing A Boat to Sail Solo

On Watch: This 60-Year-Old Hinckley Pilot 35 is Also a Working…

On Watch: America’s Cup

On Watch: All Eyes on Europe Sail Racing

Dear Readers

Chafe Protection for Dock Lines

• Sailboat Reviews

The biggest of the S2 series was offered in two layouts. The center-cockpit version is a bit ungainly looking, but offers a lot below, and like her sister is well-built. Both versions have held their value.

Leon Slikkers is a boatbuilding legend. Chris Scott, who has worked with him for over three decades, knows the story well:

“Leon grew up on a farm in Michigan. I doubt he ever saw the ocean. What stood out then, as it does now, was his craftsmanship and ingenuity. For instance, he made his own tractor from used car parts. After the war he left the farm and went to work for Chris Craft [in Holland, Michigan]. He had a good job running the shop that made hard tops, but , even with a mortage and a young family to feed, he decided to go out on his own. ‘I can build a better boat.’

“He began in his garage, building 15- and 17-foot runabouts. From there he grew Slickcraft until AMF came and bought it  in the early ’70s. The sale included a non-competition agreement for five years.

“Slikkers couldn’t sit on his money, though, so in 1973 he started S2 to build sailboats. Building on the niche that he’d established in powerboats, his original aim was a series of ‘well-detailed, nicely built, high-quality trailerables.'”

Along with the differences between sail and power, Slikkers ran into the problems of pushing premium products in a price-competitive arena. “And those early boats weren’t wonderful,” Scott says. “The joke was that S2 stood for “slowly sideways. They weren’t very salty looking, either.”

Slikkers, however, was a quick study. By the late ’70s the company had developed a full series of cruising auxiliaries. The new boats continued the Slikkers attention to detail and solid craftsmanship. Sailing performance and styling were improved, and the second wave of S2 sailboats helped people forget the ugly ducklings.

The Slikkers story continued. The “third wave” was a successful foray into high-performance boats, with the Graham & Schlagater-designed Grand Slam series—7.9 meter, 9.3, and 10.1. (The 7.9 was twice MORC National champion.) Then, in the early ’80s, Slikkers read the shrinking sailboat market and returned to building powerboats—this time the Tiara series. He retooled twice for limited orders from established sailboat classes (a fleet of 7.9s was wiped out in a hurricane, for instance) but abandoned sailboats for good in 1986.

Tiara (along with its companion line, Pursuit) still thrives. From Holland the company has grown to encompass plants in Florida and North Carolina. Leon’s sons, David and Bob, are at the helm, but Leon continues to maintain an office in the Holland plant and is “more active than you can imagine,” says Scott. Along the way he managed to acquire the assets of his original Slickcraft company at a fraction of the price that he was originally paid for it.

Introduced in 1977, the S2 11.0 reflects the maverick disposition of her makers, the quest for a better mousetrap, and the market savvy of a successful entrepreneur. She was built in both aft and center cockpit versions (roughly 160 of each type were sold). She has weathered the intervening quarter century well. The owners we queried were universally upbeat about her durability and sailing ease.

Design Often credited to the “S2 Design Team,” the 11.0 was actually designed by Arthur Edmunds. A veteran of the sailboat projects initiated by Chris Craft in the late ’60s (Commanche, Apache, et al), Edmunds was called upon by Slikkers to draft the lines for his cruisers. Largest of the bunch, the 11-meter was to combine modern sailing performance, an attractive layout, contemporary styling, and meticulous construction. Says Scott, “Leon left Arthur’s lines alone below the water, but the ‘team’ concept came from the fact that he had tremendous influence on everything else.”

Perhaps the best way to describe the 11.0’s sailing characteristics is “straight down the middle.” In an era when IOR bulges and bumps were visible even on cruising boats, Edmunds opted instead, in almost all cases, for “the mean.” Her 11′ 11″ beam is substantial, but it’s regular and fairs nicely into waterlines that give her a symmetrical “footprint” or waterplane, meaning that as she heels, her shape in the water is only minimally distorted. This is one of the sources of her light, mannerly helm.

She has the sailplan proportions of her day—masthead rig, small main, overlarge foretriangle. Modern cruisers have come to appreciate larger, controllable mainsails and smaller, more easily handled headsails, but that’s not a combination you’ll easily find in boats of her vintage.

It’s hard to recall that there was a day when all sailing controls weren’t led to the cockpit, but the 11-meter was a pioneer in that regard.

The boat has a longish fin keel that strikes a balance between the deeper, thinner foils of today and the full-length keels they’ve evolved from. In order to encapsulate the considerable (6,000-pound) ballast, however, Edmunds was forced to make the keel very thick in section. In addition to adding to parasitic drag the thick keel produces less lift than might a modern NACA-inspired or suitably engineered foil. This all tends to decree middle-of-the-pack performance, especially upwind.

Her rudder is lower in aspect ratio than those that have followed, and it is supported by a vestigal skeg. Both of these factors reduce turning efficiency, but cruisers get some compensating confidence from the protection afforded by the skeg.

Contemporary cruising boats tend to have longer waterlines and stems that are more nearly plumb than the 11-meter. There’s good reason that boats have evolved toward longer waterlines, narrower entries, and flatter waterplanes—they go faster. But yesterday’s cruisers, even yesterday’s “modern” boats like the S2, offer some compensations. Certainly the foredeck on the 11.0 is kept relatively dry by her marked overhang forward. Certainly her look is more balanced and graceful due to her overhangs fore and aft. Her reverse transom works nicely with the rising line of her overhanging counter to form one of the aesthetic achievements of the boat.

In profile we can’t help but wince a bit at her oversized windows. While they certainly make the interior brighter and more habitable, they involve three jumbo-sized cutouts in the cabin trunk—big enough to pose a risk, in our view, in breaking seas. The rest of her styling elements—the marriage between a relatively straight sheerline and a slightly forward-leaning housetop, the stem and stern angles—all work together well.

When Slikkers introduced the 11- meter, the most popular auxiliary in the world over 30 feet was Morgan’s Out Island 41, which at that time was  closing in on 500 sold. Morgan attempted to capitalize on this acceptance with a smaller boat, a 36-footer built around the same open feel, the same center cockpit convenience and aft cabin privacy that made the 41 so popular. Despite being built on the hull of a racing design and being able to sail circles around its larger Out Island cousin, the Out Island 36 didn’t come close to matching the 41’s popularity. Neither did the Out Island 33.

Is a 36-footer too small to be a good aft-cabin cruiser? Not if you’re willing to separate appearance from effectiveness. The center cockpit version of the 11.0 has a very workable layout. Passage fore and aft can be accomplished either through a passageway (with galley ranged outboard) to port or a double-doored head (to starboard). The galley is close to the companionway and in the pitching center of the boat—good for ventilation, communication, and comfort. The saloon is pinched a bit by being shoved forward, but it works. We think it would work even better if the space devoted to a navigator’s electronic center had been minimized to achieve a bit more elbow room.)

Take a look at the two versions in profile, however, and you might have second thoughts. While the aft cockpit 11.0 has a comforting familiarity, the aesthetic adjustments called for to accommodate to the tall and bulging center cockpit boat are major. And, perched way atop the thing at the wheel, how protected, comfortable, and at ease will you feel? We sailed the aft cockpit model, so this is just speculation. Suffice it to say that, in return for the privacy of well-separated cabins and the convenience of sailing the boat from the middle, there are some prices to be paid.

Construction The mid-sized sampling of owners who weighed in on the 11.0 made her durability and sound construction their central theme. Said one owner of  a center cockpit boat,  “On the trip from San Diego to Hawaii we had several days of 12- to 18-foot seas and winds up to 55 knots. The boat handled everything with no problems. We felt very safe.”

Most rate the boat’s strength, quality, and equipment as well above average. “A lot of that,” says Scott, “is the integral keel. Molding the whole boat instead of bolting the keel onto it makes it much stronger.”

The hull is solid fiberglass. The deck is cored with end-grain balsa in the way of the walkways. During the production run of the 11-meter, blisters popped their ugly heads onto the marine scene. Says Scott, “We did a lot of research right away. We had been using vinylster resin from the start. What we wound up doing was replacing the exterior layer of cloth with chopped matt to eliminate the problems caused, we felt, by the binder in the cloth. Up to that point we’d always thought the chopper gun was a quick and dirty tool that we’d never use. We were among the first in the industry to come up with a five-year anti-blister warranty in 1984.” 

Just a single owner in our sample reported blistering. His, he said, “are widely spaced and have shown no change since 1983.”

S2’s hull-deck joint is simple, well-engineered, and has held up well: The hull molding has an inward-turning flange, onto which the deck molding is dropped. The joint is bedded in a flexible sealant, and through- bolted on six-inch centers by bolts passing vertically through the entire height of the slotted aluminum toerail. The joint is also through-bolted across the stem. Deck leaks seem not to be a problem.

The chainplates, however, have been a source of aggravation to several owners. One claims that they must be rebedded every season in order to keep them watertight.

Slikkers designed and made the hatches for the 11.0, rather than buying them from a vendor. From molding the surrounding lip into the deck tooling, to shaping the Lexan, to sizing and making the gasket, developing the sealant, and cutting the teak non-skid strips that guard it, the entire operation was done in-house. “Gelcoat was the premium available,” says Scott. “Our factory was one of the first to be climate-controlled. We pioneered the practice of building the boats in the molds so that they’d have maximum support.”

The 11-meter boats were sold with a variety of engines, including Universal, Volvo, and Yanmar. We saw no engine complaints, with the exception of one Volvo MD 17C (with saildrive) that had problems with overheating until a separate through-hull was installed for raw water intake.

S2s were priced above the market average, but lots of sailors were willing to pay for what they delivered. Praise is not unanimous, however.  Though no one has reported structural problems, one sailor sees the wooden mast step and relative “lack of structural support for the keel-stepped mast” as a potential problem. The recessed grab rail atop the cabin house is also, we noticed, the sort of “finger breaker” design that is neither accessible nor hefty enough to be a useful handhold in a time of genuine need.

Performance The 11.0 displaces 15,000 pounds. That means that she doesn’t get thrown around by the waves. It also means that it takes a lot to get her going. You can make the case that weight and momentum are advantages in a seaway, but our experience, and the evolution of modern cruising design, suggests that the less weight for a given sail power, the more efficient (and certainly the more sprightly) the sailboat. The trend over the quarter century since the 11.0 was designed has been toward lighter and lighter cruisers, and there are few sailors today who feel that adding pounds adds to sailing performance.

The 11.0’s sail area/displacement ratio of 17.2 is moderate, but it’s up against a displacement/length ratio of nearly 300. She has more wetted surface (by something approaching 25 percent) than a typical modern cruiser might. She is, in short, no speed demon. The lighter the breeze and the closer into it the course, the more she tends to suffer for the design trends of her era.

Due to her stability, predictable handling, and ease of maneuvering, though, she can be fun and forgiving to sail. She’s quite stiff, despite the fact that she derives relatively little form stability from her slack-bilged hull. Her T-shaped cockpit, an innovation in its day, limits the size of the wheel (36-inch) so that steering from the rail isn’t comfortable or efficient. The cockpit is not as deep nor the coamings as high as we would like to see on a boat that ventures offshore. The cockpit locker, on the other hand, is big enough to afford access to the port side of the engine, as well as space for generator, watermaker, and plenty of stowage. Furthermore, it’s compartmentalized intelligently.

Accommodations From its oversized (6′ 5″ x 6′ 4″) forward berth to its generous (6′ 5″ x 3′ 9″) quarter berth aft, the S2’s interior is more than a little accommodating. Throw in places to sleep for three more and she truly fulfills the “boat with beds” ideal that was the controlling interior principle in the ’70s and ’80s. But she’s more than a bunkhouse. Her galley, wrapped around a “serve-through counter,” was ahead of its time in terms of function, elbow room, clever use of space, and integration with the rest of the interior.

Using the quarterberth as a seat for the nav table is an acceptable accommodation in a boat this small. A surprisingly large hanging locker, well-finished drawers, and a jumbo head with shower are among the other details that have make the boat livable.

Whether the center-cockpit version “succeeds” in your eyes depends upon the priority you put on sociability belowdecks. The necessary functions—cooking, sleeping, and head-going—receive more space and attention in the twin-cabin set-up. The saloon is nudged forward and made “cozier” in the process—not necessarily a bad thing.

Having separate cabins is a boon for couples that cruise together. If that’s what’s on your mind, the 11.0 offers a boat that’s sized and priced to make double-cabin sailing a reality. One owner, who is 6′ 5″, reports that “I not only have room to stand up and lie down, but in weeks at a time of cruising I’ve never gotten that ‘closed in’ feeling.”

Conclusions Most owners rated the 11-meter’s original equipment as good to adequate. One said, however, “make sure that primary and halyard winches are big enough. My boat had Lewmars that were very undersized. I’ve moved to #43 (primary) and #42 (halyard) respectively.” Another wrote, “The original refrigeration wasn’t adequate for living aboard. We replaced it with Adler Barbour 20 years ago and it’s still going strong.”

Superior gelcoat quality is part of the S2 reputation. Most owners are pleased with the way theirs have held up over the years. While the boats were never built with an epoxy or any other form of barrier coat, the research that Slikkers and company did in the ’80s, and the use of vinylester resin, seems to have yielded hulls that have resisted blistering well.

The boats that Slikkers built, both aft and center cockpit,  are cruisable in the extreme when it comes to accommodation and capability. The more you demand from them in terms of sailing sizzle, the more their slips show, but considering the high level of construction in the hull, deck, and cabinetry, the generally good standard equipment list, and the thoughtful design details throughout, it’s easy enough to see why these boats have held their value over the years. According to the BUC Used Boat Price Guide, a 1981 model S2 11.0 (in both center- and aft-cockpit versions) has a retail value range today between $48,000 and $52,000 (Northeast and Mid-Atlantic region).

There’s a good deal of information on S2 boats on the Web. In particular check the pages at www.angelfire.com/mi/loosecruise/S2/index.html .

Contact – Tiara Yachts, 725 E. 40th St., Holland MI, 49423; 616/392-7163; www.tiarayachts.com .

Also With This Article Click here to view “Owner’s Comments.”

RELATED ARTICLES MORE FROM AUTHOR

I bought an S2 11.0A (36′ aft cockpit) a couple of years ago. I had been looking at a Hunter Cherubini 37′ cutter rigged boat that was said to be the heartist boats built in it’s time, and seemingly blue-water capable. That deal didn’t happen, but a year later I found my 36′ S2 and in researching the vessels specifications, I saw that it wasn’t exactly a blue-water boat, but it definitely fit the mold of a coastal cruiser. 75 galons of water, 50 gallons of fuel, 36hp engine, vestigal skeg rudder and encased lead keel. The quality of construction was noted in most online articles I read; and just as most people said, I wouldn’t find any blistering of the fiberglass on this four-decades old boat, however, up until this past season, I was actually considering painting the hull, the tan gelcoat was chalky and I had always wanted a dark blue hull anyway, but that was before I spent a couple of days polising the gelcoat. The color and shine was restored to that of a much younger boat, doing that and stripping the paint off the teak toerails and oiling them, has gotten me several complments from other boaters. The S2 is shaping up to be the type of boat I’ve always admired, a vessel with classic lines, nice overhangs, moderate freeboard, a heart-shaped transom, with golden-orange teak and stainless steel glistening in the sun. But while some of those items are cosmetic, and while I haven’t been in many wicked conditions yet with this boat, I’ve been in a couple that have proven to me that those old-style overhangs, along with the overall hull shape, is a great design in large swells when winds are high and when you are plowing through oncoming wave-sets that are as close together as possible without breaking over each other. And while the interior isn’t designed with an “open plan” like a modern boat, you do have confidence in rough conditions that you’re not going to be allowed to get very far if the boat makes an unexpected movement when you’ve braced yourself in the galley while making something for the crew. What is also notable is the quality of the interior woodwork. My wife spent a couple of hours treating all the interior teak with lemon oil, which gave the woodwork a fresh luster without feeling oily or tacky. The boat is exceptionaly dry, maybe owing to the care by the single owner the boat had had for nearly 40 years, before us. But I would guess that even through multiple owners, as long as one of them didn’t go “redesigning” the interior, or exterior for that matter, any S2 would still be a boat that is functional and updateable. If you like a more classic looking boat with teak insead of aluminum, formica, or plastic, then this is a boat that was at the top of it’s class for the price at the time, and in my opinion, has aged well as far as design and looks.

LEAVE A REPLY Cancel reply

Log in to leave a comment

Latest Videos

What’s the Best Sailboats for Beginners?

Why Does A Sailboat Keel Fall Off?

The Perfect Family Sailboat! Hunter 27-2 – Boat Review

Pettit EZ-Poxy – How to Paint a Boat

Latest sailboat review.

• Privacy Policy
• Do Not Sell My Personal Information
• Online Account Activation
• Privacy Manager